Blur Busters Forums

Who you gonna call? The Blur Busters! For Everything Better Than 60Hz™ Skip to content

Firmware upgrade using Linux tool, requires no hardware

Adjusting BENQ Blur Reduction and DyAc (Dynamic Acceleration) including Blur Busters Strobe Utility. Supports most BenQ/Zowie Z-Series monitors (XL2411, XL2420, XL2720, XL2735, XL2540, XL2546)

Re: Firmware upgrade using Linux tool, requires no hardware

Postby Kbenq » 08 Oct 2018, 18:22

Sparky wrote:
Kbenq wrote:
Sparky wrote:
Kbenq wrote:
I have a problem in the last step, when I enter the code ./flashrom, it throws me an error of ./flashrom not found.
pleas help me, my monitor is Benq XL2420z
Are you in the right place?
You can use pwd to see what directory you're in, and ls to see what's there.


I've been two days with this and I can not, I do not know how to load the bin, I'm new to linux but I came well in the part where it is used *. / flashrom*, that is, if I have an answer from my monitor, if it is correctly identified, please help me

Code: Select all
pwd
is the command to show the present working directory.
Code: Select all
ls
lists the contents of the current directory.
Code: Select all
cd [directory]
is the command to change directory.
Code: Select all
.
is the shortcut for the current directory, so if you try to run ./something then that something should be in the current directory.

Either the program isn't where it's supposed to be, or you're in the wrong place to be running that command. With the information you've given, we can't tell which.


Code: Select all
ubuntu@ubuntu:~$ sudo modprobe i2c-dev
ubuntu@ubuntu:~$ sudo i2cdetect -l
i2c-3   i2c          nvkm-0000:07:00.0-aux-0004         I2C adapter
i2c-13   i2c          nvkm-0000:07:00.0-aux-0009         I2C adapter
i2c-1   i2c          nvkm-0000:07:00.0-bus-0002         I2C adapter
i2c-11   i2c          nvkm-0000:07:00.0-aux-0008         I2C adapter
i2c-8   i2c          nvkm-0000:07:00.0-bus-0007         I2C adapter
i2c-6   i2c          nvkm-0000:07:00.0-bus-0006         I2C adapter
i2c-4   i2c          nvkm-0000:07:00.0-bus-0005         I2C adapter
i2c-14   i2c          0000:07:00.0                       I2C adapter
i2c-2   i2c          nvkm-0000:07:00.0-bus-0004         I2C adapter
i2c-12   i2c          nvkm-0000:07:00.0-bus-0009         I2C adapter
i2c-0   i2c          nvkm-0000:07:00.0-bus-0001         I2C adapter
i2c-9   i2c          nvkm-0000:07:00.0-aux-0007         I2C adapter
i2c-10   i2c          nvkm-0000:07:00.0-bus-0008         I2C adapter
i2c-7   i2c          nvkm-0000:07:00.0-aux-0006         I2C adapter
i2c-5   i2c          nvkm-0000:07:00.0-aux-0005         I2C adapter
ubuntu@ubuntu:~$ sudo i2cdetect 21
Error: Could not open file `/dev/i2c-21' or `/dev/i2c/21': No such file or directory
ubuntu@ubuntu:~$ sudo i2cdetect 2
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-2.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- 37 -- -- 3a 3b -- -- -- --
40: -- -- -- -- -- -- -- -- -- 49 -- -- -- -- -- --
50: 50 -- -- -- -- -- -- -- -- 59 -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --                         
ubuntu@ubuntu:~$ sudo i2cdump -r 0-127 2 0x50
No size specified (using byte-data access)
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-2, address 0x50, mode byte
Probe range limited to 0x00-0x7f.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: 00 ff ff ff ff ff ff 00 09 d1 2d 7f 45 54 00 00    ........??-?ET..
10: 07 18 01 03 80 35 1e 78 2e 9d e1 a6 54 54 9f 26    ?????5?x.???TT?&
20: 0d 50 54 a5 6b 80 d1 c0 45 7c 61 7c 81 80 81 bc    ?PT?k???E|a|????
30: 95 3c 31 7c 01 01 02 3a 80 18 71 38 2d 40 58 2c    ?<1|???:??q8-@X,
40: 45 00 13 2a 21 00 00 1e 00 00 00 ff 00 4d 32 45    E.?*!..?.....M2E
50: 30 32 32 34 33 53 4c 30 0a 20 00 00 00 fd 00 38    02243SL0? ...?.8
60: 90 1e a0 21 00 0a 20 20 20 20 20 20 00 00 00 fc    ???!.?      ...?
70: 00 42 65 6e 51 20 58 4c 32 34 32 30 5a 0a 01 e5    .BenQ XL2420Z???
ubuntu@ubuntu:~$ sudo ./flashrom -p mstarddc_spi
sudo: ./flashrom: command not found
ubuntu@ubuntu:~$ sudo ./flashrom -p mstarddc_spi:dev=/dev/i2c-2:49
sudo: ./flashrom: command not found

I can not get past this point
Kbenq
 
Posts: 5
Joined: 08 Oct 2018, 14:22

Re: Firmware upgrade using Linux tool, requires no hardware

Postby BFone » 09 Oct 2018, 17:58

Did you download the flashrom folder from one of the links I ve given, copy it to your user-folder or whereever to the ubuntu system and run the following commands:

Code: Select all
cd flashrom     <<< or whatever neccessary is, to change inside the flashrom folder
make -j

I can't see this part in your log, which you have posted ...
BFone
 
Posts: 4
Joined: 21 Sep 2018, 21:37

Re: Firmware upgrade using Linux tool, requires no hardware

Postby TheMoeBlob » 11 Oct 2018, 12:43

@BFone your method seems to have worked, just doing the final steps now so thank you very much
TheMoeBlob
 
Posts: 2
Joined: 17 Sep 2018, 17:21

Re: Firmware upgrade using Linux tool, requires no hardware

Postby Kbenq » 13 Oct 2018, 14:45

BFone wrote:Did you download the flashrom folder from one of the links I ve given, copy it to your user-folder or whereever to the ubuntu system and run the following commands:

Code: Select all
cd flashrom     <<< or whatever neccessary is, to change inside the flashrom folder
make -j

I can't see this part in your log, which you have posted ...

Ready, you can update my monitor, the problem is that I was using Ubuntu ver. 16 ..... and download version 14 .... and I could read the FLASHROM folder without problems, only that at the end when the verification was made, I throw ERROR IN VERIFICATION, I was scared because I did not turn on the monitor, but if did it and if it appears with the V004 watch, would there be a problem for it?
Kbenq
 
Posts: 5
Joined: 08 Oct 2018, 14:22

Previous

Return to BENQ/Zowie Tweaking — Strobe Utility / Blur Reduction / DyAc

Who is online

Users browsing this forum: No registered users and 2 guests